|Table of Contents|

Review on Reverse Engineering of Freeform Surface(PDF)

南京师范大学学报（工程技术版）[ISSN:1006-6977/CN:61-1281/TN]

Issue:
2005年03期
Page:
45-49
Research Field:
Publishing date:

Info

Title:
Review on Reverse Engineering of Freeform Surface
Author(s):
ZHENG Ying1;  LI Jian2
1.College of Computer and Information Technology, Henan Normal University, Henan Xinxiang, 453007, China; 2. College of Computer and Information Engineering, Shaanxi University of Science and Technology, Shaanxi Xianyang, 712081, China
Keywords:
freeform sur face;  m easure p lann ing;  reverse eng ineer ing
PACS:
TP391.7;
DOI:
-
Abstract:
Reve rse eng inee ring is an im portan t technology in realizing the duplica tion and m odify ing of freefo rm sur face parts, wh ich inc ludes m easur ing, m odeling, m anufacturing and inspecting of freefo rm surface. The paper stud ies the current research status of m easurem en t path plann ing, surface reconstruction of measured po ints and integ rated techno logy or iented to the reverse eng ineering of free fo rm surface. Discusses the prob lem s ex isted in the measurem ent path planning such as the adaptive layout of the m easured po ints and the optim ization o f the m easurem ent path, and proposes them ethod to so lve the prob lems. It a lso stud ies them ode ling and d irectly manu factur ing o f comp licated sur face based on them easured po ints respective ly in the surface reconstruc tion, and in addition, in troduces the deve lop m en t of the m easur ing m ode ling and m anufacturing integrated techno logy to realize the integ ration o f the above tech no logy wh ich included in the reverse eng ineering of the freeform surface, and finally ana ly zes the developing tendency and key problem s o f the techno logy.

References:

[ 1] Kam C L. A Geom etr ic decom pos ition m ethod for part prog ramm ing of CMM S [ J ]. Au toFact Europe Con,f 13.15- 13.24.
[ 2] Pahk H J. Deve lopm en t o f computer-a ided inspection sys tem w ith CMM for integ rated m o ld m anufacturing [ J]. Anna ls of the C IRP, 1993( 42) : 557- 560.
[ 3] Ko sterM. Curvature-dependent param eter ization o f curves and surface[ J]. Computer-A ided Design, 1991, 23( 8): 569- 579.
[ 4] L i S Z. Adaptive sam pling and m esh generation [ J]. Com puterA ided Design, 1995, 27( 3): 235 -240.
[ 5] 来新民. 基于计算机视觉的自由曲面逆向工程关键技术研究[ D]. 天津: 天津大学, 1997.
[ 6] Terzopoulos D T, V asilescuM. Samp ling and reconstruc tion w ith adaptive meshes[ A ]. Proc IEEE Comput Soc Con f Com puter V ision and Pattern Recogn ition [ C ]. 1991. 70- 75.
[ 7] Ahn C H, Lee S. A se lf-o rgan ization Neura lN etwork ap pro ach for automa tic m esh generation [ J]. IEEE T rans M agnetic, 1991, 27( 5): 4201- 4204.
[ 8] M enq Ch iaH siang, Yau H ongT zong, La iGw anYw an. Au tom ated prec ision measurem ent of surface profile in CADd irected inspection [ J]. IEEE T ransactions on Robotics and Autom ation, 1992, 8( 2): 268- 278.
[ 9] 高国军, 陈康宁, 林志航, 等. 用三坐标测量机检测自由曲面时检测点和路径的规划方法研究[ J]. 西安交通大学学报, 1996, 30( 7) : 57 -63.
[ 10] 李健, 王文, 陈子辰. 自由曲面零件寻位自适应检测方法研究[ J]. 仪器仪表学报, 2002, 23 ( 5): 530- 534.
[ 11] 王平江. 曲面测量、建模及数控加工集成研究[ D]. 武汉: 华中理工大学, 1996.
[ 12] Sm ith K B. M ulti-Laser disp lacem ent sensor used in ac cura te dig itizing techn ique [ J ]. Transactions of the ASME, Journa l of Eng inee ring for Industry, 1994, 116 ( 11): 482 -490.
[ 13] Zhang F Y, NeeA Y, Fuh JY, et al. A N eural netw ork approach to determ in ing optim a l inspection sam pling size fo r CMM [ J]. Compu ter Integrated M anu factu ring Sys tem, 1996, 9( 3) : 161- 169.
[ 14] 白作霖, 赵汝嘉, 张定红, 等. 基于坐标测量机的自由曲面误差评定方法[ J] . 中国机械工程, 1995, 6 ( 6): 1274- 1280

Memo

Memo:
-
Last Update: 2013-04-29